Off-Road Vehicles / 3 min read

Bed Racks for a 2024 Toyota Tundra 5.5-Foot Bed

Compare three verified bed-rack part numbers for a U.S. 2024 Toyota Tundra SR5 TRD Off-Road 4x4 CrewMax with an uncovered 5.5-foot bed and factory deck rails.

By 4x4Outdoors · Research-based guide · Reviewed · Our approach

Reviewed truck

U.S. 2024 Toyota Tundra SR5 TRD Off-Road · CrewMax · 5-foot-6-inch bed · Third generation

The reviewed truck has the 3.4L i-FORCE gas V6, part-time 4WD and the factory 5.5-foot short bed. Toyota lists 65.6 inches of inside bed length. Start with the uncovered composite bed and intact factory Deck Rail System, clear of a tonneau, cap, drop-in liner and accessory hardware that could block the mounts. Check where you can use the tie-down cleats after installation.

Toyota 2024 Tundra SR5, Deck Rail System and CrewMax bed dimensions · Toyota 2024 Tundra owner’s manual and load guidance

Compare three verified part numbers

Scroll across to compare rack setups.

Part numbers, mounting, clearance and load limits for the reviewed vehicle
Rack system Cali Raised LED Low Profile Overland Bed Rack Leitner Designs ACS FORGED with Sliding Rear Bar Front Runner by Dometic Pro Bed Rack Kit with Slimline II Tray
Part numbers CR393204-62-FA-1511PBTT002T
Required adapters and hardware No separate rack adapter listed.No separate rack adapter listed.No separate rack adapter listed.
Mounting method Bolts to factory Deck Rail System. No drilling or cutting.Main rails bolt to Deck Rails. Drill rear pillars for the braces.Front brackets use Deck Rails. Rear stiffeners use bed bolts and drilled holes.
Clearance and restrictions Check under-bar clearance and access to rail cleats.Check sliding-bar travel and access to tie-down cleats.Check side loading and access to anchors around support legs.
Vehicle load limit Use the door-label payload and axle ratings. Count occupants, the rack, accessories, cargo and any trailer tongue weight.
Rack load limit 400 lb dynamic · 750 lb parked, manufacturer recommendations. 800 lb on-road · 400 lb off-road · 1,400 lb parked. Rating source for Leitner Designs ACS FORGED with Sliding Rear Bar No separate rating verified for this setup. Manufacturer documentation for Front Runner by Dometic Pro Bed Rack Kit with Slimline II Tray

Use the lowest applicable vehicle, rack and accessory limit for your driving conditions. Select a rack name for its fitment sources and details.

Cali Raised LED

Low Profile Overland Bed Rack

Part number
CR3932
Mounting
The rack bolts to the factory side deck rails using the included hardware. Cali Raised specifies no drilling or cutting for this installation.
Before ordering
The low-profile crossbars keep gear closer to the bed. Measure clearance underneath for coolers, cases and access to the rail cleats.

Leitner Designs

ACS FORGED with Sliding Rear Bar

Part number
04-62-FA-1511
Mounting
The main rails bolt to the factory side deck rails. This sliding-bar version also requires drilling at the rear bed pillars and fitting rivet nuts for the support braces.
Before ordering
The rear load bar slides to open up space for taller cargo. Check the brace positions and where the original tie-down cleats can be used before installing.

Front Runner by Dometic

Pro Bed Rack Kit with Slimline II Tray

Part number
PBTT002T
Mounting
The front brackets use plates in the factory deck rails. The rear stiffeners use the factory bed bolt locations and require additional drilled holes near the rear bed pillars.
Before ordering
PBTT002T includes the full Slimline II tray. Check that the side supports leave room for loading from the sides and that you can reach the anchors you need.

Check the whole setup before buying

  • Send the exact part number and photos of your rails and installed accessories to the rack maker if your truck differs from the configuration above.
  • Measure clearance for the cab, tailgate, cargo and any tent or bike mount. Verify that the rack and its load clear the lights and cameras you use.
  • Check the truck’s payload and axle limits with passengers, rack, mounts and cargo on board. Use the applicable rack and accessory limits for driving on pavement, driving off-road, and parking with a load.