Off-Road Vehicles / 3 min read

Bed Racks for a 2024 Ford F-250 Super Duty 6¾-Foot Bed

Compare Kuat, Putco and Front Runner bed racks for a U.S. 2024 Ford F-250 Super Duty Lariat Tremor with the 6¾-foot bed. See part numbers and mounts.

By 4x4Outdoors · Research-based guide · Reviewed · Our approach

Reviewed truck

U.S. 2024 Ford F-250 Super Duty Lariat Tremor · Crew Cab · 6-foot-9-inch bed · 2023 redesign

The reviewed truck has the 7.3L gas V8, four-wheel drive, single rear wheels and the uncovered factory short box. Ford calls it the 6¾-foot box. Rack makers may list the same application as 6 ft 9 in or Super Duty short bed. This comparison assumes factory bed rails and stake pockets clear of a tonneau, drop-in liner, toolboxes or other hardware. Check fit separately for the 8-foot box.

Ford 2024 Lariat Tremor eligibility and 7.3L engine · Ford 2024 F-250 Crew Cab 6¾-foot box configuration · Ford Super Duty owner’s manual and vehicle loading guidance

Compare three verified part numbers

Scroll across to compare rack setups.

Part numbers, mounting, clearance and load limits for the reviewed vehicle
Rack system Kuat IBEX Heavy Duty Short Bed Putco Venture TEC Rack Front Runner by Dometic Pro Bed Rack Kit with Slimline II Tray
Part numbers IBEXD3184200PBFF003T
Required adapters and hardware No separate rack adapter listed.Use the Ford-specific stake-pocket hardware.PBFF003 brackets come with the kit.
Mounting method Included bed clamps grip below the rails. No drilling.Stake-pocket brackets use rear U-brackets.Drill front bed walls and rear pillars. Remove taillights for access.
Clearance and restrictions Check clamp seating and access at mid or full height.Clear the rail caps and verify access to tie-downs.Check access to cargo below the tray.
Vehicle load limit Use the door-label payload and axle ratings. Count occupants, the rack, accessories, cargo and any trailer tongue weight.
Rack load limit 300 lb driving · 1,200 lb parked. Rating source for Kuat IBEX Heavy Duty Short Bed 600 lb dynamic · 300 lb off-road dynamic · 1,000 lb parked. Rating source for Putco Venture TEC Rack No separate rating verified for this setup. Manufacturer documentation for Front Runner by Dometic Pro Bed Rack Kit with Slimline II Tray

Use the lowest applicable vehicle, rack and accessory limit for your driving conditions. Select a rack name for its fitment sources and details.

Kuat

IBEX Heavy Duty Short Bed

Part number
IBEXD3
Mounting
Kuat lists this frame for the F-250 short bed. It uses the included universal bed clamps under the factory bed rails without drilling. The kit includes two crossbars.
Before ordering
Choose full or mid height during assembly. Check that the clamps can seat flat under the rail and that the crossbar position leaves room for the cargo you want to reach.
View specs and listings for Küat IBEX Heavy Duty Short Bed — IBEXD3

Putco

Venture TEC Rack

Part number
184200
Mounting
Putco lists this rack for the F-250 6-foot-9-inch bed. The Ford installation supplement shows stake-pocket brackets and rear U-brackets that engage the inside of the stake pockets.
Before ordering
The rack leaves the bed open between the uprights. Inspect the plastic rail caps for access to all four pockets and check that you can still reach the bed tie-downs.
View specs and listings for Putco Venture TEC Rack — 184200

Front Runner by Dometic

Pro Bed Rack Kit with Slimline II Tray

Part number
PBFF003T
Mounting
The kit includes the Slimline II tray and Pro Bed System. The PBFF003 bracket instructions call for drilling at the front bed walls and rear bed pillars. The rear mounting steps require removing the taillights for access.
Before ordering
The tray provides a broad deck above the bed. Account for the rack’s own weight in your payload and check that you can reach gear below it.
View specs and listings for Front Runner Pro Bed Rack Kit — PBFF003T

Check the whole setup before buying

  • Send the exact part number and photos of your rails and installed accessories to the rack maker if your truck differs from the configuration above.
  • Measure clearance for the cab, tailgate, cargo and any tent or bike mount. Verify that the rack and its load clear the lights and cameras you use.
  • Check the truck’s payload and axle limits with passengers, rack, mounts and cargo on board. Use the applicable rack and accessory limits for driving on pavement, driving off-road, and parking with a load.