Trailer hub maintenance / 5 min read
Trailer wheel bearing and hub maintenance guide
Identify the axle, check the service interval, and match trailer wheel bearings, seals, grease, and tools to the hub.

Identify the axle and hub before ordering parts
Find the axle tag or serial number and record the trailer model, axle maker, and axle rating. Use that information to find the axle’s service manual and parts list. Save the bearing cone and cup numbers, seal number or dimensions, and the spindle’s retention hardware. Record the details for each axle if the trailer has been repaired or modified.
Dexter lists K71-717-00 for compatible 3,500 lb axle assemblies. The reviewed kit lists L68149 and L44649 bearing cones and their corresponding cups. Those numbers help you check a match. A 3,500 lb rating on a different axle leaves the spindle, hub, and seal dimensions to verify. If a number is unreadable, ask a parts supplier to identify the assembly using the axle serial number.
Identify the lubrication system too. A conventional grease hub, a greaseable spindle, an oil bath hub, and a sealed cartridge can have different service instructions. The dust cap alone may give an incomplete picture. Check the axle documentation before buying a grease gun or opening the hub.
Set the service interval for your trailer
Start with the manufacturer’s interval for your specific axle. Dexter’s bearing FAQ gives 12 months or 12,000 miles for bearing lubrication. Use the instructions for your axle and service conditions, including any separate guidance for immersion or storage. If you bought a used trailer with an unknown service history, establish a baseline before a long trip.
Look for grease or oil around the cap, the inside of the wheel, and the brake backing plate. New noise, grinding, looseness, or a wheel that runs unusually hot calls for inspection. If a problem appears on the road, pull over in a safe location and arrange help if you cannot check or move the trailer safely. A warm hub can have more than one cause, including brake drag.
Inspect the bearings, cups, and seal surfaces
Work on a stable surface, chock the trailer, and use the trailer maker’s lift and support points with equipment rated for the load. Use stands to support the trailer while you work. Check the axle procedure before removing the hub, especially on a braked axle where grease and loose parts can reach the braking surfaces.
The service manual explains how to clean and inspect the rollers and cups. Pitting, scoring, or discoloration warrants evaluation. Keep bearing sets organized by wheel position during inspection. When replacing a damaged bearing, follow the manufacturer’s instructions for replacing its matching cup. Check the spindle and the seal running surface before closing up the hub.
A Lisle 56750 can pull an accessible old seal. Make sure the hook can engage it without scoring the bore. Have the correct new seal and a suitable installer ready. If there is grease on the brakes, address the leak and have the affected brake parts evaluated before towing.
Check the seal direction and installed depth in the axle manual. Before fitting the new seal, clean the hub bore and inspect it for marks that might let lubricant escape. If the bore or spindle is damaged, get it evaluated before installing parts. Dexter calls for replacing the seals before lubricating an E-Z Lube hub that has been removed.
Choose the specified lubricant and tool
Match the lubricant to the axle manual. If the existing grease is unknown, ask the axle maker about compatibility and how to change over. Use clean tools and keep lubricant off friction surfaces. Label the grease gun or packer so you can tell which grease it contains at the next service.
For removed bearings, the Lisle 34550 handles bearings up to 3-1/2 in outside diameter. A Lincoln 1134 manual grease gun is an option when the axle maker specifies a hand gun for a compatible fitting. Dexter’s E-Z Lube instructions call for a hand-operated gun and rotation of the hub during lubrication. Follow that procedure only on the covered axle. Fresh grease at a fitting leaves the rollers, cups, and seal out of view, so keep the scheduled inspection.
Check adjustment, brakes, and wheel fastening
Follow the axle instructions for bearing adjustment, retainer installation, and any endplay check. The trailer or wheel manual gives the applicable wheel fastener torque and recheck schedule. Keep bearing adjustment and wheel fastening separate in your service notes.
Read the adjustment instructions for the exact retention design. Dexter’s manual has separate procedures for the standard cotter pin and the E-Z Lube nut retainer. Lay out the correct retainer and tools before you begin. If the adjustment cannot be checked with the equipment you have, have a trailer shop complete that step.
Before departure, verify the cap is seated, the hub turns as the manual describes, and the brakes operate. Record the date, mileage, and parts installed. If the hub leaks, develops play, or sounds rough after service, have it checked before the next trip.
- Identify the axle, hub, and lubrication system.
- Match the bearing cones, cups, seal, and retaining hardware.
- Gather the approved lubricant, support equipment, and correct tools.
- Find the adjustment and wheel fastening instructions before lifting.
- Log the service and check for leaks and proper brake operation.
Sources & further reading
These sources support the factual reference points in this guide. Practical comparisons and packing suggestions are editorial guidance.
- Dexter service manual for bearing inspection, seals, and adjustment
- Dexter bearing lubrication and service interval FAQ
- Dexter E-Z Lube system overview and inspection guidance
- Dexter wheel bearing kit application bulletin
- Lisle 34550 bearing packer specifications
- Lisle 56750 seal puller specifications
- SKF Lincoln manual grease gun catalog