Trailer tires & TPMS / 5 min read

Trailer tires and TPMS guide for weekend towing

Choose a replacement trailer tire, check cold pressure and tread, and set up a trailer tire pressure monitoring system for towing.

By 4x4Outdoors · Research-based guide · Reviewed · Our approach

Illustrative vehicle and ground tent at a wooded campsite
Illustrative editorial image. This guide draws on published research.

Match the tire to the trailer placard

Start with the trailer’s tire and loading label, certification label, and owner’s manual. Record the specified tire size, cold inflation pressure, and axle ratings. Compare those with the tires actually installed. A previous owner may have changed wheels or tires, so a sidewall on the trailer today is only one piece of the fit check.

For example, Goodyear lists Endurance part 724861519 as ST205/75R15, load range D, with a maximum single-tire load of 2,150 lb at 65 PSI cold. That figure describes this size and load range. Follow the trailer maker’s cold pressure specification for the approved configuration. Ask the trailer maker or a qualified tire shop to confirm the setup if the labels and installed parts disagree.

Check the approved rim width and wheel and valve pressure limits, along with clearance to fenders and nearby tires. Weigh the loaded trailer and compare actual loads with the trailer and axle limits. Uneven loading can put more weight on one tire even when the axle total is within its rating. A higher-rated replacement tire leaves the original axle and trailer ratings in place.

Check cold pressure and the spare

Check each road tire and the spare with a hand gauge before driving. Do it while the tires are cold, preferably before the trailer leaves home or the campsite. Write the target pressure where you can find it without opening a manual on the shoulder. The tow vehicle may use a different pressure, so keep its numbers separate.

The JACO ElitePro analog gauge covers 5–100 PSI. Check the range against the trailer and the spare before buying. If the valve sits behind a wheel cover, verify you can seat the chuck squarely. Carry an air source rated for the pressure you need and make sure its hose can reach the farthest wheel while connected to its power source.

Pressure normally rises as the tires warm. Check again when cold before resetting pressure. If a tire repeatedly loses pressure, find the cause before towing. Ask a tire shop to inspect the valve, wheel, and tire if the cause is unclear.

Inspect tread, sidewalls, and tire age

Look at both sidewalls where accessible, along with the tread face. Cuts, bulges, exposed material, and unusual wear call for inspection. With a tread depth gauge, sample the main grooves across the face and around the tire. Place the probe away from raised wear bars. The JACO TreadPro gives numbered readings in 1/32 in increments and tops out at 14/32 in.

Look for the four-digit date portion of the DOT tire identification number. For example, 2424 means the 24th week of 2024. The full code may be on the inward-facing sidewall. Follow the tire and trailer makers’ inspection and replacement guidance, and include the spare in those checks. A trailer that spends most of the year parked can have substantial tread left when its tires need attention.

Choose and set up trailer TPMS

Count the wheels you want to monitor. A tandem-axle trailer typically needs four sensors for the road wheels, and a spare takes another sensor if you want it monitored. Verify the sensor’s pressure range, valve stem requirements, display power, and signal path from the farthest wheel. Check whether the kit includes the repeater or lists it as an accessory.

The TST 507 TST-507-RV-4-C includes four cap sensors, a color display, and a repeater. TST lists these cap sensors for compatible rubber or metal stems. Its flow-through sensors have a separate metal stem requirement. Check clearance to the wheel and valve access with the sensor installed. Cap sensors have to come off for a conventional chuck, while internal sensors generally require tire service to install.

Pair each sensor to its actual wheel location and confirm that all positions report from the cab. Set the alarms using the system manual and the trailer’s cold pressure baseline. A gauge reading gives you a useful cross-check before towing. Label sensor positions if you remove them for storage or move them when the wheels are serviced.

Respond to an alert and finish the departure check

If pressure drops or a temperature alert persists, pull over where you can inspect safely. Identify the wheel on the display, then check the tire, valve, and pressure. A missing reading calls for a signal and sensor check. Until that wheel reports again, you have no live reading from that position. Arrange roadside help if you cannot safely inspect the wheel or if damage or rapid air loss makes continuing unsafe.

Confirm the spare fits its intended position and that you have the correct jack, wheel tools, and trailer lifting instructions. Pack the pressure gauge where you can reach it without unloading the trailer.

  • Match size, load range, wheel ratings, and the approved cold pressure.
  • Check pressure and inspect the road tires and spare.
  • Confirm the gauge range, valve access, and inflator reach.
  • Verify every TPMS position, repeater power, and alarm settings before towing.
  • Confirm the spare and wheel tools fit, and keep roadside contact details handy.

Sources & further reading

These sources support the factual reference points in this guide. Practical comparisons and packing suggestions are editorial guidance.